# Boiler Installation North York | Replacement & Combi

URL: https://boilerinstallationtoronto.ca/service-areas/north-york/

![](/images/misc/service-van-parked-in-a-residential-gta-driveway-a.webp)

Toronto Boiler Installation

[/ →](/)

# Boiler Installation North York: High-Efficiency, Combi, Replacement and Hydronic Heating Service Across Willowdale and Don Mills

Last updated: October 27, 2026

\[Toronto Boiler Installation\](/) provides high-efficiency boiler installation, cast iron radiator retrofits, combi boiler installations, and hydronic heating rebuilds throughout North York, ON, backed by 22 years of TSSA G1/G2 licensed boiler service. Our technicians install Viessmann Vitodens 100, Weil-McLain WM97+, Navien NCB-E, Bosch Greenstar, and Buderus SSB condensing units on Willowdale mid-century homes, Bayview Village estates, Don Mills 1960s bungalows, Bathurst Manor split-levels, and Lansing pre-war properties with mixing valves, primary-secondary piping, and PVC direct venting. North York combi installations run $4,500 to $8,500 CAD, condensing retrofits $6,500 to $12,000 CAD, and cast iron heritage replacements $8,500 to $14,500 CAD, with Enbridge Home Efficiency Rebate Plus and Canada Greener Homes Grant coordination on qualifying installs.

**North York Cost Anchor:** North York retrofits run $8,500-$14,500 CAD for older cast iron, $5,500-$9,500 CAD for newer combi swaps. Combi boiler installation runs $4,500 to $8,500 CAD and a 95%+ AFUE condensing unit $6,500 to $12,000 CAD, with combined Enbridge and federal rebates offsetting up to $11,500 CAD.

Call (647) 254-9788

[tel:+16472549788 →](tel:+16472549788)

 

Request Written Installation Quote

[/contact/ →](/contact/)

-   M-series (North York)
-   Same-day GTA dispatch, 4-hour cold-snap response
-   TSSA G1/G2 Licensed Crew

-   Willowdale
-   Don Mills
-   Bayview Village

-   5-Star Customer Satisfaction
-   Same-Day GTA Emergency Dispatch
-   22 Years of Boiler Installation Experience
-   Written Workmanship Warranty

Common Objections

## What Actually Stops GTA Homeowners From Replacing an Aging Boiler

Four objections come up on almost every call. Here is the straight answer to each, with the CAD numbers attached.

### 1\. “The quote is huge, I am being oversold”

A high-efficiency condensing swap runs $6,500 to $12,000 CAD because it includes a new condensate line, PVC flue rework, near-boiler piping, expansion tank, zone controls, and the TSSA permit. Every line item appears on the quote in CAD. Combined Enbridge and federal rebates offset up to $11,500 CAD.

### 2\. “You cannot tell if the technician is really licensed”

Ontario requires TSSA G1 or G2 certification for gas boiler work, plus CSA B51 for large-BTU pressure vessels. Certificate numbers appear on every invoice and TSSA permit numbers appear on completed work.

### 3\. “Nobody publishes the price”

Our four CAD scope bands are published on this page: diagnostic $99 to $249, standard repair $200 to $1,200, major repair $1,200 to $3,500, and full combi installation $4,500 to $8,500. High-efficiency condensing runs $6,500 to $12,000 CAD.

### 4\. “The boiler is 25 years old, repair or replace?”

Cast iron lasts 30 to 50 years but drops to 60 to 70 percent efficiency by year 25. A modern 95% AFUE unit cuts natural gas bills 25 to 35 percent, qualifies for up to $11,500 CAD in rebates, and pays back in 6 to 10 years. You get a written repair-versus-replace on every diagnostic.

Talk it through with a licensed technician

[tel:+16472549788 →](tel:+16472549788)

Local Housing Stock

## What Boilers in North York Actually Look Like

Mid-century housing stock where boilers reach the 25-40 year replacement window.

**Typical failure pattern:** Heat exchanger corrosion on aging mid-century boilers, prompting replacement.

**Postal codes served:** M-series (North York). Covering Willowdale, Don Mills, Bayview Village and the surrounding neighbourhoods, under City of Toronto (North York).

North York retrofits run $8,500-$14,500 CAD for older cast iron, $5,500-$9,500 CAD for newer combi swaps.

-   Same-day GTA dispatch, 4-hour cold-snap response
-   22 years serving North York and Toronto
-   TSSA G1/G2 technicians covering Willowdale, Don Mills and Bayview Village
-   4-hour cold-snap response

![Basement mechanical room with a condensing boiler in a North York home](/images/misc/older-brick-home-basement-mechanical-room-with-cas.webp)

## Our Boiler Services in North York

\[Toronto Boiler Installation\](/) provides high-efficiency boiler installation, cast iron radiator retrofits, combi boiler installations, and hydronic heating rebuilds throughout North York, ON, backed by 22 years of TSSA G1/G2 licensed boiler service. Our technicians install Viessmann Vitodens 100, Weil-McLain WM97+, Navien NCB-E, Bosch Greenstar, and Buderus SSB condensing units on Willowdale mid-century homes, Bayview Village estates, Don Mills 1960s bungalows, Bathurst Manor split-levels, and Lansing pre-war properties with mixing valves, primary-secondary piping, and PVC direct venting. North York combi installations run $4,500 to $8,500 CAD, condensing retrofits $6,500 to $12,000 CAD, and cast iron heritage replacements $8,500 to $14,500 CAD, with Enbridge Home Efficiency Rebate Plus and Canada Greener Homes Grant coordination on qualifying installs.

 

![Wall-mounted 95%+ AFUE condensing boiler installed in a Toronto basement with copper near-boiler piping and PVC flue](/images/misc/wall-mounted-95-percent-afue-condensing-boiler-new.webp) Most Requested

### High-Efficiency Condensing Boiler Installation Toronto

95%+ AFUE condensing boiler installation with 316L stainless heat exchangers, ECM circulators, and PVC concentric venting, backed by 22 years of TSSA G1/G2 licensed experience on Viessmann Vitodens, Weil-McLain Evergreen, Navien NFC, and Bosch Greenstar units. Installation runs $6,500 to $12,000 CAD with combined Enbridge Home Efficiency Rebate Plus and Canada Greener Homes Grant offsetting up to $11,500 CAD.

$6,500 - $12,000 CAD

[High-Efficiency Condensing Boiler Installation Toronto →](/high-efficiency-boiler-installation-toronto/)

 

![Wall-mounted combi boiler installed in a compact Toronto utility room with isolation valves and domestic hot water piping](/images/misc/compact-wall-mounted-combi-boiler-installed-in-a-s.webp) Space Saver

### Combi Boiler Installation Toronto

Wall-mounted combi boiler installation with plate heat exchangers, ECM pumps, and descaling flush valves for GTA hard water, backed by 22 years of TSSA G1/G2 licensed retrofit experience on Navien NCB-E, Viessmann Vitodens 100-W, Rinnai i090SN, and Bosch Greenstar Combi units. Combi installations run $4,500 to $8,500 CAD, sized by GPM demand for homes under 2,500 sq ft.

$4,500 - $8,500 CAD

[Combi Boiler Installation Toronto →](/combi-boiler-installation-toronto/)

![Toronto Boiler Installation crew breaking down an old cast iron sectional boiler beside its new condensing replacement](/images/misc/old-cast-iron-sectional-boiler-being-broken-down-f.webp)

### Boiler Replacement Toronto

End-of-life gas boiler replacement for 15 to 40 year old cast iron sectional systems, backed by 22 years of TSSA G1/G2 licensed retrofit experience installing Viessmann Vitodens, Weil-McLain WM97+, and Navien NFC condensing units. Retrofits run $8,500 to $14,500 CAD, with combined Enbridge Home Efficiency Rebate Plus and Canada Greener Homes Grant offsetting up to $11,500 CAD.

$8,500 - $14,500 CAD

[Boiler Replacement Toronto →](/boiler-replacement-toronto/)

![Cascading commercial condensing boilers in a Toronto mid-rise mechanical room with common venting header](/images/misc/two-cascading-commercial-condensing-boilers-mounte.webp)

### Commercial Boiler Installation Toronto

Commercial rooftop and mechanical-room boiler installation to ASME pressure vessel code, CSA B51, and ASHRAE 90.1 standards, backed by 22 years of TSSA large-boiler certified experience on Lochinvar Crest, Viessmann Vitocrossal 300, Weil-McLain SlimFit, and Bradford White Copper Brute units with N+1 redundancy and low-NOx burners. Commercial installations run $8,500 to $18,000 CAD.

$8,500 - $18,000 CAD

[Commercial Boiler Installation Toronto →](/commercial-boiler-installation-toronto/)

![Restored cast iron column radiator with a thermostatic radiator valve in a pre-war Toronto living room](/images/misc/restored-cast-iron-column-radiator-with-a-thermost.webp)

### Hydronic Heating and Radiator Installation Toronto

Hydronic heating design with cast iron column radiators, baseboard convectors, thermostatic radiator valves, and oxygen-barrier PEX manifolds, backed by 22 years of TSSA G1/G2 licensed experience installing Runtal panels, Buderus Logatrend, tekmar controls, and Grundfos ALPHA circulators. Hydronic retrofits run $3,500 to $12,000 CAD, commissioned to CSA B214 with system balance verification.

$3,500 - $12,000 CAD

[Hydronic Heating and Radiator Installation Toronto →](/hydronic-heating-installation-toronto/)

![Oxygen-barrier PEX radiant loops laid across a Toronto basement slab before pour, with the manifold on the wall behind](/images/misc/oxygen-barrier-pex-radiant-loops-stapled-to-insula.webp)

### In-Floor Radiant Heating Toronto

In-floor radiant heating with 12-inch on-center PEX loops, thermostatic mixing valves, return-water temperature protection, and tekmar 260 outdoor reset controls, backed by 22 years of TSSA G1/G2 licensed radiant experience installing Uponor AquaPEX, Rehau RAUPEX, and Watts Radiant systems. Radiant retrofits run $8,000 to $20,000 CAD, staple-up or slab-on-grade to CSA B214.

$8,000 - $20,000 CAD

[In-Floor Radiant Heating Toronto →](/in-floor-radiant-heating-toronto/)

 

![Toronto Boiler Installation technician using a digital flue gas analyser during an annual 12-point boiler tune-up](/images/misc/technician-holding-a-digital-flue-gas-analyser-wit.webp) Best Value

### Boiler Maintenance and Annual Service Toronto

Annual 12-point boiler tune-up with digital combustion analysis, CO/CO2 ratio verification, expansion tank pre-charge testing, water pH checks, and pressure relief valve inspection, backed by 22 years of TSSA G1/G2 licensed maintenance service on Viessmann, Weil-McLain, Navien, Bosch, Buderus, and IBC systems. Annual maintenance runs $199 to $349 CAD, preserving manufacturer warranties.

$199 - $349 CAD

[Boiler Maintenance and Annual Service Toronto →](/boiler-maintenance-toronto/)

![Toronto Boiler Installation technician testing an ignition control board inside an opened boiler casing](/images/misc/technician-with-a-multimeter-testing-an-ignition-c.webp)

### Boiler Repair Toronto

Boiler repair for aquastats, control boards, gas valves, ignition modules, circulator pumps, and heat exchangers, backed by 22 years of TSSA G1/G2 licensed diagnostic experience on Viessmann, Weil-McLain, Navien, Bosch, Buderus, and IBC systems. Standard repairs run $200 to $1,200 CAD, major heat exchanger work $1,200 to $3,500 CAD with diagnostic waived on same-visit authorisation.

$200 - $3,500 CAD

[Boiler Repair Toronto →](/boiler-repair-toronto/)

 

![Technician diagnosing a failed boiler during an emergency no-heat call in a Toronto basement](/images/misc/technician-with-a-work-light-and-tool-case-diagnos.webp) 24/7 Dispatch

### Emergency Boiler Repair Toronto

24 hour emergency boiler repair with 4-hour cold-snap dispatch for no-heat calls, red-tag clearance, ignition-lockout troubleshooting, and frozen condensate line clearance, backed by 22 years of TSSA G1/G2 licensed emergency service on Viessmann, Weil-McLain, Navien, Bosch, and Buderus systems. After-hours diagnostic runs $199 to $349 CAD, same-day component repair $200 to $1,200 CAD.

$199 - $349 CAD

[Emergency Boiler Repair Toronto →](/emergency-boiler-repair-toronto/)

Why Choose Us

## Why North York Homeowners Replace With Us

-   22 Years of Boiler Installation Experience across Toronto and the GTA
-   Written repair-versus-replace analysis on every diagnostic, no pressure
-   Cast iron retrofits $8,500 to $14,500 CAD, newer combi swaps $5,500 to $9,500 CAD
-   Chimney liner de-commissioning and direct-vent wall penetration handled in scope
-   TSSA G1 and G2 licensed, Ontario Building Code Part 6 and Part 7 compliant
-   Old unit disposal and scrap recycling included in the quoted price

The Framework

## How Our North York Boiler Installation Works, 6 Steps

From the first call to the rebate cheque, here is exactly what happens and in what order.

1.  1
    
    ### Site assessment
    
    Postal code, home age, distribution type, existing AFUE, and heating load in BTU per square foot. Same-day or next-morning visit.
    
2.  2
    
    ### Manual J heat load and sizing
    
    Written heat load with boiler capacity sized to the actual home load. No oversizing, which is what causes short cycling.
    
3.  3
    
    ### Written quote, three options
    
    Combi, split system, and high-efficiency retrofit priced in CAD with parts, labour, permits, disposal, and rebate offset per option.
    
4.  4
    
    ### TSSA permit and scheduling
    
    Ontario Building Code Part 6 compliance verified. Installation within 3 to 7 business days standard, 24 to 48 hours on emergencies.
    
5.  5
    
    ### Installation and commissioning
    
    Boiler installed to CSA B51, near-boiler piping to ASHRAE 90.1, condensate neutralised, combustion analysis with a CO monitor, system purged and rebalanced.
    
6.  6
    
    ### Verification and rebate filing
    
    TSSA inspection where required, warranty registration filed, Enbridge and Canada Greener Homes paperwork submitted, written workmanship warranty issued.
    

## Need a boiler quote in North York?

Published CAD pricing, TSSA-licensed technicians, and same-day dispatch across the whole coverage area.

(647) 254-9788

[tel:+16472549788 →](tel:+16472549788)

 

Get CAD Quote

[/contact/ →](/contact/)

## Covering Willowdale, Don Mills and Bayview Village

North York dispatch runs on Highway 401, the Don Valley Parkway, and Highway 404 with Yonge Street, Bayview Avenue, Sheppard Avenue, and Lawrence Avenue East as the local connectors. Willowdale sits along Yonge north of Sheppard, Don Mills east of the valley, and Bayview Village between the two. Same-day dispatch covers the North York M-series postal codes.

Access here is easier than Old Toronto. Most mid-century homes have a driveway and a walk-out or side entrance to the basement, so old boiler removal and new equipment delivery are straightforward. That keeps install days to a single working day on a standard swap.

Cold-snap response is four hours. Because so many North York boilers are in the 25 to 40 year band, a no-heat call here more often ends in a replacement decision than a repair, which is why we bring the full CAD scope band sheet to every emergency visit.

## Mid-Century North York Boilers Are Hitting the Wall

Willowdale, Don Mills, and Bayview Village were built out through the 1950s and 1960s. The original boilers were replaced once in the 1990s, which puts a large share of the current equipment at 25 to 35 years old right now. That is the exact window where a cast iron sectional drops to 60 to 70 percent efficiency and the heat exchanger starts showing corrosion.

The warning signs are consistent: rust staining around the base of the unit, a small persistent pressure loss that needs topping up every few weeks, a flue that shows condensation where it should be dry, and gas bills rising year over year with no change in habits. By the time water is visibly leaking, the sectional is usually already cracked.

Distribution in North York is mixed. Some homes run cast iron or steel radiators and are good candidates for a condensing retrofit that keeps the radiators. Others were converted to hydronic baseboard in a 1990s renovation and take a straight combi or condensing swap. Both are quoted from the same published CAD bands.

-   End-of-life replacement on 25 to 40 year old mid-century boilers
-   Heat exchanger corrosion diagnosis with written repair-versus-replace
-   Cast iron and steel radiator retrofits that keep existing distribution
-   Chimney liner de-commissioning when moving to PVC direct venting
-   Gas line sizing, isolation valves, disposal and scrap recycling

Customer Feedback

## What North York Customers Say

> Willowdale boiler was 30 years old with a corroded heat exchanger. Full replacement with a condensing unit for $9,600 CAD.

Diana R.

Willowdale

5-Star Customer Satisfaction

> Don Mills home, combi swap. Clear CAD options and a new unit installed for $7,300 CAD.

Patrick S.

Don Mills

Top-Rated Contractor

> Bayview Village annual service caught a failing pressure relief valve before winter. Twelve-point tune-up for $289 CAD.

Yvonne T.

Bayview Village

Trusted by Homeowners and Businesses

Get a Quote

## Tell Us What Your Boiler Is Doing

Short form, no gatekeeping. A TSSA-licensed technician follows up with a written CAD quote for North York, and the diagnostic fee comes off the invoice when you authorise the work on the same visit.

-   Four published CAD scope bands, never gated
-   Same-day GTA dispatch, 4-hour cold-snap response
-   Enbridge and Canada Greener Homes paperwork filed for you
-   Written workmanship warranty on labour

### Thanks, we have your message.

A TSSA-licensed technician follows up within one business day.

## Request a Written Installation Quote

Send the details and a TSSA-licensed technician follows up with an itemised CAD quote. No email address required from us, no quote gating from you.

Local Questions

## Boiler Installation North York: Frequently Asked Questions

### How fast can you reach Willowdale or Don Mills?

Same-day dispatch covers the North York M-series postal codes and cold-snap no-heat calls get a technician within four hours. Crews route on Highway 401, the Don Valley Parkway, and Sheppard Avenue.

### What does a boiler replacement cost in North York?

North York retrofits run $8,500 to $14,500 CAD where older cast iron distribution is retained and $5,500 to $9,500 CAD for newer combi swaps. A standard 95%+ AFUE condensing installation is $6,500 to $12,000 CAD. Rebates offset up to $11,500 CAD combined.

### How do I know if my heat exchanger is corroded?

Rust staining at the base of the unit, pressure that needs topping up every few weeks, condensation in a flue that should be dry, and gas bills climbing without a change in habits. A combustion analysis and a visual inspection confirm it, and you get the finding in writing.

### Is my 30-year-old boiler worth repairing?

Sometimes, and we will say so if it is. A cast iron sectional can run 30 to 50 years, but efficiency drops to 60 to 70 percent by year 25. The written repair-versus-replace analysis compares the repair cost against remaining life, projected gas savings from a 95%+ AFUE unit, and the rebate offset.

### Do you remove and dispose of the old boiler?

Yes. Removal, disposal, and scrap recycling are included in the quoted price, along with the gas line sizing, isolation valves, permits, and labour. Nothing on that list is billed as an extra afterwards.

### What happens to my chimney if I go high-efficiency?

A condensing boiler vents through PVC, not the masonry chimney, so the flue is de-commissioned for the boiler. If a water heater still shares that chimney, the liner is resized for the remaining appliance. That work is quoted in scope, not discovered later.

### Do you cover Lawrence Manor, York Mills and Bathurst Manor?

Yes. The full North York M-series coverage includes Lawrence Manor, York Mills, Bathurst Manor, Newtonbrook, Hoggs Hollow, and Flemingdon Park.

### Can I keep my radiators on a mid-century home?

Yes, where the distribution is cast iron or steel radiators. Pairing them with a condensing boiler needs a mixing valve, an outdoor reset curve, and return-water temperature protection, which keeps the unit condensing for most of the heating season.

### Still have a question about your boiler?

Talk to a TSSA-licensed technician. Same-day GTA dispatch, 4-hour cold-snap response.

(647) 254-9788

[tel:+16472549788 →](tel:+16472549788)

 

Request Written Installation Quote

[/contact/ →](/contact/)

## Boiler Service Coverage in North York

Get Directions

[https://www.google.com/maps/dir/?api=1&destination=43.7615,-79.4111 →](https://www.google.com/maps/dir/?api=1&destination=43.7615,-79.4111)

## We Also Cover These Areas Near North York

Boiler Installation TorontoOlder Toronto cast iron systems run $8,500-$14,500 CAD for a full high-efficiency retrofit. View Toronto page

[/service-areas/toronto/ →](/service-areas/toronto/)

 

Boiler Installation MarkhamMarkham hydronic and combi systems run $5,500-$9,500 CAD for a swap; radiant work scales with zone count. View Markham page

[/service-areas/markham/ →](/service-areas/markham/)

 

Boiler Installation ScarboroughScarborough retrofits run $8,500-$14,500 CAD for older cast iron, $5,500-$9,500 CAD for newer combi swaps. View Scarborough page

[/service-areas/scarborough/ →](/service-areas/scarborough/)

![](/images/misc/tssa-licensed-technician-closing-the-front-panel-o.webp)

Same-Day Emergency Dispatch, 24/7 Cold Snap Response

## Book Boiler Installation in North York

Same-day dispatch with a four hour cold-snap response, and an itemised CAD quote before any work starts.

Call (647) 254-9788

[tel:+16472549788 →](tel:+16472549788)

 

Request Written Installation Quote

[/contact/ →](/contact/)

-   Written workmanship warranty
-   Published CAD pricing, no quote gating
-   TSSA G1/G2 licensed technicians
