# Boiler Installation Etobicoke | Combi & Condensing

URL: https://boilerinstallationtoronto.ca/service-areas/etobicoke/

![](/images/misc/service-van-parked-in-a-residential-gta-driveway-a.webp)

Toronto Boiler Installation

[/ →](/)

# Boiler Installation Etobicoke: High-Efficiency, Combi, Replacement and Hydronic Heating Service Across The Kingsway and Mimico

Last updated: October 27, 2026

\[Toronto Boiler Installation\](/) provides high-efficiency boiler installation, cast iron radiator retrofits, combi boiler swaps, and commercial condo mechanical service throughout Etobicoke, ON, backed by 22 years of TSSA G1/G2 licensed boiler experience. Our technicians install Viessmann Vitodens 100, Weil-McLain WM97+, Navien NFC, Bosch Greenstar, Buderus SSB, and Lochinvar Crest units on Kingsway heritage homes, Mimico waterfront condos, Long Branch bungalows, Islington estates, and Alderwood post-war properties with 316L stainless heat exchangers, ECM circulators, and primary-secondary hydraulic separators. Etobicoke condensing installations run $6,500 to $12,000 CAD, Kingsway heritage retrofits $8,500 to $14,500 CAD, commercial condo mechanical work $8,500 to $18,000 CAD, and Enbridge plus Canada Greener Homes rebates coordinated on qualifying installs.

**Etobicoke Cost Anchor:** Etobicoke retrofits run $8,500-$14,500 CAD for older cast iron, $5,500-$9,500 CAD for newer combi swaps. Combi boiler installation runs $4,500 to $8,500 CAD and a 95%+ AFUE condensing unit $6,500 to $12,000 CAD, with combined Enbridge and federal rebates offsetting up to $11,500 CAD.

Call (647) 254-9788

[tel:+16472549788 →](tel:+16472549788)

 

Request Written Installation Quote

[/contact/ →](/contact/)

-   M-series (Etobicoke)
-   Same-day GTA dispatch, 4-hour cold-snap response
-   TSSA G1/G2 Licensed Crew

-   The Kingsway
-   Mimico
-   Long Branch

-   5-Star Customer Satisfaction
-   Same-Day GTA Emergency Dispatch
-   22 Years of Boiler Installation Experience
-   Written Workmanship Warranty

Common Objections

## What Actually Stops GTA Homeowners From Replacing an Aging Boiler

Four objections come up on almost every call. Here is the straight answer to each, with the CAD numbers attached.

### 1\. “The quote is huge, I am being oversold”

A high-efficiency condensing swap runs $6,500 to $12,000 CAD because it includes a new condensate line, PVC flue rework, near-boiler piping, expansion tank, zone controls, and the TSSA permit. Every line item appears on the quote in CAD. Combined Enbridge and federal rebates offset up to $11,500 CAD.

### 2\. “You cannot tell if the technician is really licensed”

Ontario requires TSSA G1 or G2 certification for gas boiler work, plus CSA B51 for large-BTU pressure vessels. Certificate numbers appear on every invoice and TSSA permit numbers appear on completed work.

### 3\. “Nobody publishes the price”

Our four CAD scope bands are published on this page: diagnostic $99 to $249, standard repair $200 to $1,200, major repair $1,200 to $3,500, and full combi installation $4,500 to $8,500. High-efficiency condensing runs $6,500 to $12,000 CAD.

### 4\. “The boiler is 25 years old, repair or replace?”

Cast iron lasts 30 to 50 years but drops to 60 to 70 percent efficiency by year 25. A modern 95% AFUE unit cuts natural gas bills 25 to 35 percent, qualifies for up to $11,500 CAD in rebates, and pays back in 6 to 10 years. You get a written repair-versus-replace on every diagnostic.

Talk it through with a licensed technician

[tel:+16472549788 →](tel:+16472549788)

Local Housing Stock

## What Boilers in Etobicoke Actually Look Like

Mix of older and newer housing stock spanning cast iron retrofits and combi swaps.

**Typical failure pattern:** Cast iron retrofit in older enclaves or combi swap in newer areas depending on the neighbourhood.

**Postal codes served:** M-series (Etobicoke). Covering The Kingsway, Mimico, Long Branch and the surrounding neighbourhoods, under City of Toronto (Etobicoke).

Etobicoke retrofits run $8,500-$14,500 CAD for older cast iron, $5,500-$9,500 CAD for newer combi swaps.

-   Same-day GTA dispatch, 4-hour cold-snap response
-   22 years serving Etobicoke and Toronto
-   TSSA G1/G2 technicians covering The Kingsway, Mimico and Long Branch
-   4-hour cold-snap response

![Basement mechanical room with a condensing boiler in a Etobicoke home](/images/misc/older-brick-home-basement-mechanical-room-with-cas.webp)

## Our Boiler Services in Etobicoke

\[Toronto Boiler Installation\](/) provides high-efficiency boiler installation, cast iron radiator retrofits, combi boiler swaps, and commercial condo mechanical service throughout Etobicoke, ON, backed by 22 years of TSSA G1/G2 licensed boiler experience. Our technicians install Viessmann Vitodens 100, Weil-McLain WM97+, Navien NFC, Bosch Greenstar, Buderus SSB, and Lochinvar Crest units on Kingsway heritage homes, Mimico waterfront condos, Long Branch bungalows, Islington estates, and Alderwood post-war properties with 316L stainless heat exchangers, ECM circulators, and primary-secondary hydraulic separators. Etobicoke condensing installations run $6,500 to $12,000 CAD, Kingsway heritage retrofits $8,500 to $14,500 CAD, commercial condo mechanical work $8,500 to $18,000 CAD, and Enbridge plus Canada Greener Homes rebates coordinated on qualifying installs.

 

![Wall-mounted 95%+ AFUE condensing boiler installed in a Toronto basement with copper near-boiler piping and PVC flue](/images/misc/wall-mounted-95-percent-afue-condensing-boiler-new.webp) Most Requested

### High-Efficiency Condensing Boiler Installation Toronto

95%+ AFUE condensing boiler installation with 316L stainless heat exchangers, ECM circulators, and PVC concentric venting, backed by 22 years of TSSA G1/G2 licensed experience on Viessmann Vitodens, Weil-McLain Evergreen, Navien NFC, and Bosch Greenstar units. Installation runs $6,500 to $12,000 CAD with combined Enbridge Home Efficiency Rebate Plus and Canada Greener Homes Grant offsetting up to $11,500 CAD.

$6,500 - $12,000 CAD

[High-Efficiency Condensing Boiler Installation Toronto →](/high-efficiency-boiler-installation-toronto/)

 

![Wall-mounted combi boiler installed in a compact Toronto utility room with isolation valves and domestic hot water piping](/images/misc/compact-wall-mounted-combi-boiler-installed-in-a-s.webp) Space Saver

### Combi Boiler Installation Toronto

Wall-mounted combi boiler installation with plate heat exchangers, ECM pumps, and descaling flush valves for GTA hard water, backed by 22 years of TSSA G1/G2 licensed retrofit experience on Navien NCB-E, Viessmann Vitodens 100-W, Rinnai i090SN, and Bosch Greenstar Combi units. Combi installations run $4,500 to $8,500 CAD, sized by GPM demand for homes under 2,500 sq ft.

$4,500 - $8,500 CAD

[Combi Boiler Installation Toronto →](/combi-boiler-installation-toronto/)

![Toronto Boiler Installation crew breaking down an old cast iron sectional boiler beside its new condensing replacement](/images/misc/old-cast-iron-sectional-boiler-being-broken-down-f.webp)

### Boiler Replacement Toronto

End-of-life gas boiler replacement for 15 to 40 year old cast iron sectional systems, backed by 22 years of TSSA G1/G2 licensed retrofit experience installing Viessmann Vitodens, Weil-McLain WM97+, and Navien NFC condensing units. Retrofits run $8,500 to $14,500 CAD, with combined Enbridge Home Efficiency Rebate Plus and Canada Greener Homes Grant offsetting up to $11,500 CAD.

$8,500 - $14,500 CAD

[Boiler Replacement Toronto →](/boiler-replacement-toronto/)

![Cascading commercial condensing boilers in a Toronto mid-rise mechanical room with common venting header](/images/misc/two-cascading-commercial-condensing-boilers-mounte.webp)

### Commercial Boiler Installation Toronto

Commercial rooftop and mechanical-room boiler installation to ASME pressure vessel code, CSA B51, and ASHRAE 90.1 standards, backed by 22 years of TSSA large-boiler certified experience on Lochinvar Crest, Viessmann Vitocrossal 300, Weil-McLain SlimFit, and Bradford White Copper Brute units with N+1 redundancy and low-NOx burners. Commercial installations run $8,500 to $18,000 CAD.

$8,500 - $18,000 CAD

[Commercial Boiler Installation Toronto →](/commercial-boiler-installation-toronto/)

![Restored cast iron column radiator with a thermostatic radiator valve in a pre-war Toronto living room](/images/misc/restored-cast-iron-column-radiator-with-a-thermost.webp)

### Hydronic Heating and Radiator Installation Toronto

Hydronic heating design with cast iron column radiators, baseboard convectors, thermostatic radiator valves, and oxygen-barrier PEX manifolds, backed by 22 years of TSSA G1/G2 licensed experience installing Runtal panels, Buderus Logatrend, tekmar controls, and Grundfos ALPHA circulators. Hydronic retrofits run $3,500 to $12,000 CAD, commissioned to CSA B214 with system balance verification.

$3,500 - $12,000 CAD

[Hydronic Heating and Radiator Installation Toronto →](/hydronic-heating-installation-toronto/)

![Oxygen-barrier PEX radiant loops laid across a Toronto basement slab before pour, with the manifold on the wall behind](/images/misc/oxygen-barrier-pex-radiant-loops-stapled-to-insula.webp)

### In-Floor Radiant Heating Toronto

In-floor radiant heating with 12-inch on-center PEX loops, thermostatic mixing valves, return-water temperature protection, and tekmar 260 outdoor reset controls, backed by 22 years of TSSA G1/G2 licensed radiant experience installing Uponor AquaPEX, Rehau RAUPEX, and Watts Radiant systems. Radiant retrofits run $8,000 to $20,000 CAD, staple-up or slab-on-grade to CSA B214.

$8,000 - $20,000 CAD

[In-Floor Radiant Heating Toronto →](/in-floor-radiant-heating-toronto/)

 

![Toronto Boiler Installation technician using a digital flue gas analyser during an annual 12-point boiler tune-up](/images/misc/technician-holding-a-digital-flue-gas-analyser-wit.webp) Best Value

### Boiler Maintenance and Annual Service Toronto

Annual 12-point boiler tune-up with digital combustion analysis, CO/CO2 ratio verification, expansion tank pre-charge testing, water pH checks, and pressure relief valve inspection, backed by 22 years of TSSA G1/G2 licensed maintenance service on Viessmann, Weil-McLain, Navien, Bosch, Buderus, and IBC systems. Annual maintenance runs $199 to $349 CAD, preserving manufacturer warranties.

$199 - $349 CAD

[Boiler Maintenance and Annual Service Toronto →](/boiler-maintenance-toronto/)

![Toronto Boiler Installation technician testing an ignition control board inside an opened boiler casing](/images/misc/technician-with-a-multimeter-testing-an-ignition-c.webp)

### Boiler Repair Toronto

Boiler repair for aquastats, control boards, gas valves, ignition modules, circulator pumps, and heat exchangers, backed by 22 years of TSSA G1/G2 licensed diagnostic experience on Viessmann, Weil-McLain, Navien, Bosch, Buderus, and IBC systems. Standard repairs run $200 to $1,200 CAD, major heat exchanger work $1,200 to $3,500 CAD with diagnostic waived on same-visit authorisation.

$200 - $3,500 CAD

[Boiler Repair Toronto →](/boiler-repair-toronto/)

 

![Technician diagnosing a failed boiler during an emergency no-heat call in a Toronto basement](/images/misc/technician-with-a-work-light-and-tool-case-diagnos.webp) 24/7 Dispatch

### Emergency Boiler Repair Toronto

24 hour emergency boiler repair with 4-hour cold-snap dispatch for no-heat calls, red-tag clearance, ignition-lockout troubleshooting, and frozen condensate line clearance, backed by 22 years of TSSA G1/G2 licensed emergency service on Viessmann, Weil-McLain, Navien, Bosch, and Buderus systems. After-hours diagnostic runs $199 to $349 CAD, same-day component repair $200 to $1,200 CAD.

$199 - $349 CAD

[Emergency Boiler Repair Toronto →](/emergency-boiler-repair-toronto/)

Why Choose Us

## Why Etobicoke Homeowners Choose Us

-   22 Years of Boiler Installation Experience across Toronto and the GTA
-   Heritage radiator retrofits on The Kingsway, $8,500 to $14,500 CAD
-   Combi swaps in Mimico and Long Branch, $5,500 to $9,500 CAD
-   Narrow-lot vent routing measured and confirmed before quote, not on install day
-   TSSA G1 and G2 licensed, B149 clearance compliance documented
-   Enbridge and Canada Greener Homes rebate paperwork filed for you

The Framework

## How Our Etobicoke Boiler Installation Works, 6 Steps

From the first call to the rebate cheque, here is exactly what happens and in what order.

1.  1
    
    ### Site assessment
    
    Postal code, home age, distribution type, existing AFUE, and heating load in BTU per square foot. Same-day or next-morning visit.
    
2.  2
    
    ### Manual J heat load and sizing
    
    Written heat load with boiler capacity sized to the actual home load. No oversizing, which is what causes short cycling.
    
3.  3
    
    ### Written quote, three options
    
    Combi, split system, and high-efficiency retrofit priced in CAD with parts, labour, permits, disposal, and rebate offset per option.
    
4.  4
    
    ### TSSA permit and scheduling
    
    Ontario Building Code Part 6 compliance verified. Installation within 3 to 7 business days standard, 24 to 48 hours on emergencies.
    
5.  5
    
    ### Installation and commissioning
    
    Boiler installed to CSA B51, near-boiler piping to ASHRAE 90.1, condensate neutralised, combustion analysis with a CO monitor, system purged and rebalanced.
    
6.  6
    
    ### Verification and rebate filing
    
    TSSA inspection where required, warranty registration filed, Enbridge and Canada Greener Homes paperwork submitted, written workmanship warranty issued.
    

## Need a boiler quote in Etobicoke?

Published CAD pricing, TSSA-licensed technicians, and same-day dispatch across the whole coverage area.

(647) 254-9788

[tel:+16472549788 →](tel:+16472549788)

 

Get CAD Quote

[/contact/ →](/contact/)

## Reaching The Kingsway, Mimico and Long Branch

Etobicoke dispatch runs on the Gardiner Expressway, Highway 427, and Highway 401 with Bloor Street West, Lake Shore Boulevard West, and Royal York Road as the local connectors. The Kingsway sits north around Bloor and Royal York, Mimico and Long Branch south along Lake Shore. Same-day dispatch covers the Etobicoke M-series postal codes.

Lakeshore condo and low-rise buildings in Mimico and Long Branch have their own access rules. Service elevator booking, loading dock hours, and building management approval all have to be arranged before the install day, and we handle that as part of scheduling rather than turning up and finding the elevator booked.

Cold-snap response is four hours. On the older Kingsway homes a no-heat call usually involves an original distribution system, so the first step is confirming the loop is not air-locked or frozen before assuming the boiler is the fault.

## Two Etobicoke Patterns: Heritage North, Newer South

The Kingsway was built through the 1920s and 1930s and looks a lot like Old Toronto in mechanical terms. Homes run cast iron column radiators on what started as gravity hot water distribution, and the boilers have been replaced once or twice. Retrofits here keep the radiators and rebuild the near-boiler piping, expansion tank, and controls around a condensing unit with return-water temperature protection.

Mimico and Long Branch are different. Post-war houses, mid-century low-rise, and newer infill dominate, and the heating equipment is more often a wall-mounted combi or a sealed condensing boiler. Those are like-for-like swaps sized by simultaneous hot water demand, in the $5,500 to $9,500 CAD range.

The overlap is venting. Lakeshore lots are narrow and side-wall vent terminations have to respect clearances to windows, gas meters, and the neighbouring property line. That is measured at the assessment, because a vent route that does not work is the most expensive thing to discover on install day.

-   Kingsway cast iron retrofits with mixing valves and return-water protection
-   Mimico and Long Branch combi swaps sized by simultaneous GPM
-   Narrow-lot side-wall vent routing within B149 clearance rules
-   Condo and low-rise mechanical room access coordinated with building management
-   Gravity hot water conversion to pumped, zoned distribution

Customer Feedback

## What Etobicoke Customers Say

> The Kingsway heritage home kept its radiators. Condensing retrofit with mixing valves for $10,900 CAD.

Bianca L.

The Kingsway

5-Star Customer Satisfaction

> Mimico combi replaced same week. Transparent CAD quote, installed for $7,000 CAD.

Derek H.

Mimico

Top-Rated Contractor

> Long Branch boiler pump was seized. Replaced with an ECM circulator and rebalanced for $1,050 CAD.

Nadia S.

Long Branch

Trusted by Homeowners and Businesses

Get a Quote

## Tell Us What Your Boiler Is Doing

Short form, no gatekeeping. A TSSA-licensed technician follows up with a written CAD quote for Etobicoke, and the diagnostic fee comes off the invoice when you authorise the work on the same visit.

-   Four published CAD scope bands, never gated
-   Same-day GTA dispatch, 4-hour cold-snap response
-   Enbridge and Canada Greener Homes paperwork filed for you
-   Written workmanship warranty on labour

### Thanks, we have your message.

A TSSA-licensed technician follows up within one business day.

## Request a Written Installation Quote

Send the details and a TSSA-licensed technician follows up with an itemised CAD quote. No email address required from us, no quote gating from you.

Local Questions

## Boiler Installation Etobicoke: Frequently Asked Questions

### How fast can you reach The Kingsway or Mimico?

Same-day dispatch covers the Etobicoke M-series postal codes and cold-snap no-heat calls get a technician within four hours. Crews route on the Gardiner Expressway, Highway 427, Bloor Street West, and Lake Shore Boulevard West.

### What does boiler installation cost in Etobicoke?

Etobicoke retrofits run $8,500 to $14,500 CAD where older cast iron distribution is kept, typical of The Kingsway, and $5,500 to $9,500 CAD for newer combi swaps in Mimico and Long Branch. Rebates offset up to $11,500 CAD combined.

### Can I keep the radiators in my Kingsway home?

Yes. Cast iron column radiators pair well with a condensing boiler once you add a mixing valve, an outdoor reset curve, and return-water temperature protection. Keeping the distribution avoids opening plaster for ductwork and preserves the quiet, even heat those radiators give.

### My lot is narrow. Will a side-wall vent even fit?

In most cases yes, but it has to be measured. B149 sets clearances to windows, doors, gas meters, and the property line, and on a narrow Lakeshore lot the workable route is often a concentric termination at a specific height. We confirm the route at the assessment, before the quote.

### Do you work in Mimico condos and low-rise buildings?

Yes. Service elevator booking, loading dock hours, and building management approval are arranged as part of scheduling. Replacement equipment is sized to the existing mechanical closet and the building's fixed vent run.

### Do you cover Islington Village, Alderwood and New Toronto?

Yes. The full Etobicoke M-series coverage includes Islington Village, Alderwood, New Toronto, Humber Bay, Markland Wood, and Rexdale.

### My heating loop has cold spots. Is the boiler failing?

Often not. Cold spots on an older gravity-converted system usually mean trapped air or an unbalanced loop. Air elimination with a Spirovent or air scoop and a proper balance pass fixes it. We check that before recommending equipment.

### Which rebates apply in Etobicoke?

Enbridge Home Efficiency Rebate Plus up to $6,500 CAD, Canada Greener Homes Grant up to $5,000 CAD, and Canada Greener Homes Loan up to $40,000 CAD at 0% interest. We file the paperwork as an ENERGY STAR certified installer.

### Still have a question about your boiler?

Talk to a TSSA-licensed technician. Same-day GTA dispatch, 4-hour cold-snap response.

(647) 254-9788

[tel:+16472549788 →](tel:+16472549788)

 

Request Written Installation Quote

[/contact/ →](/contact/)

## Boiler Service Coverage in Etobicoke

Get Directions

[https://www.google.com/maps/dir/?api=1&destination=43.6205,-79.5132 →](https://www.google.com/maps/dir/?api=1&destination=43.6205,-79.5132)

## We Also Cover These Areas Near Etobicoke

Boiler Installation TorontoOlder Toronto cast iron systems run $8,500-$14,500 CAD for a full high-efficiency retrofit. View Toronto page

[/service-areas/toronto/ →](/service-areas/toronto/)

 

Boiler Installation MississaugaNewer Mississauga hydronic systems run $5,500-$9,500 CAD for a combi swap. View Mississauga page

[/service-areas/mississauga/ →](/service-areas/mississauga/)

 

Boiler Installation North YorkNorth York retrofits run $8,500-$14,500 CAD for older cast iron, $5,500-$9,500 CAD for newer combi swaps. View North York page

[/service-areas/north-york/ →](/service-areas/north-york/)

![](/images/misc/tssa-licensed-technician-closing-the-front-panel-o.webp)

Same-Day Emergency Dispatch, 24/7 Cold Snap Response

## Book Boiler Installation in Etobicoke

Same-day dispatch with a four hour cold-snap response, and an itemised CAD quote before any work starts.

Call (647) 254-9788

[tel:+16472549788 →](tel:+16472549788)

 

Request Written Installation Quote

[/contact/ →](/contact/)

-   Written workmanship warranty
-   Published CAD pricing, no quote gating
-   TSSA G1/G2 licensed technicians
